Design working out of the conceptual case of lemeshno-otvalniy plough on the basis of geometrical modeling
DOI:
https://doi.org/10.18372/2415-8151.1.5968Keywords:
Working surface, combination of constructions, smooth plugging, constructive and projective geometrical models.Abstract
Design–project of the conceptual body of mould–board plough based on geometrical modeling. In article, it is considering design–project of the conceptual body of mould–board plough based on methods of constructive and projective geometrical modeling. The decision of task in view by a combination of several constructions is given. The problem is executed 2D and 3D modeling in system AutoCAD.References
Bosoy E.S. Teoriya, konstruktsiya i raschet selskohozyaystvennyih mashin. /E.S. Bosoy, O.V. Vernyaev, I.I. Smirnov, E.G. Sultan-Shah; Pod red. Bosogo E.S. - M .: Mashinostroenie, 1978.- 568 s.
Gyachev L.V. Osnovyi teorii i rascheta lemeshno-otvalnyih poverhnostey. Barnaul - 1989 -92 s.
E.Tyalve. Kratkiy kurs promyishlennogo dizayna.
Per. s angl. P. A. Kunina. - M .: Mashinostroenie, 1984, 192 s., Il.
Product design Principles, Tools and Techniques. Concept Selection. ME 1007 Design Principles. http://www.twirpx.com.
V.I. Korabelskiy., A.V. Spirin, I.M. Kovalova. Osobennosti proektirovaniya gruntoobrobnoi tehniki s uchetom agrotehnologichnih i ekologicheskih trebovaniy http://www.nbuv.gov.ua/Portal/natural/Geotm/2008_79/04.pdf.
D.V. Voloshinov. Teoriya avtomatizatsii proektirovaniya ob'ektov i protsessov na osnove metodov konstruktivnogo geometricheskogo medelirovaniya. Rabota diss.dokt.tehn.nauk. - SPb., - 2010.
Bliev A.A. Obosnovanie tehnologicheskoy shemyi pluga dlya gladkoy dvuh'yarusnoy vspashki. Rabota diss. na soisk. uchenoy stepeni k.t.n. - Moskva, - VIM, -1992. - 22s.
Dubanov A. A. Metodyi i algoritmyi approksimatsii tehnicheskih poverhnostey razvertyivayuschimisya. Rabota diss. na soisk. uchenoy stepeni k.t.n. MUPP, 1997.
Ryazanov A.V. Obosnovanie parametrov uglosnimom k korpusu oborotnogo pluga. Diss. na soisk.uchenoy stepeni k.t.n. Yangiyul 2002. 141s.
Kuchkarova D.F., Zhuraeva T.H. Modelirovanie napravlyayuschey krivoy lemeshno-otvalnoy poverhnosti zadaniem konki. Prikladnaya geometriya i inzhenernaya grafika. Mezhvedomstvennyiy nauchno-tehnicheskiy sbornik. Vyipusk # 87. - M., - 2011. - 248-252 s.
Zhuraeva T.H. Voprosyi optimizatsii geometricheskih parametrov rabochih organov s lemeshno-otvalnoy poverhnostyu. Trudyi mezhdunarodnoy nauchno-metodicheskoy konferentsii «Sovremennoe sostoyanie, razvitie inzhenernoy geometrii i kompyuternoy grafiki v usloviyah informatsionnyih i kompyuternyih tehnologiy». - Almatyi, 16-17 noyabrya, - 2011g. - 183-193 s.
Zhuraeva T.H., Hidirov S.Z. Primenenie 2D modeley pri 3D modelirovanii rabochih poverhnostey otvalov na AutoCAD. «GRAFIKA XXI VEKA» Tezisyi dokladov HIV Vseukrainskoy studencheskoy nauchno-tehnicheskoy konferentsii. Sevastopol, 3-7 oktyabrya 2011g. - 128-131 s.
