ACOUSTIC ENERGY AT CHANGE OF TREATED COMPOSITE MATERIAL DISPERSION PROPERTIES

Authors

  • Sergii Filonenko National Aviation University

DOI:

https://doi.org/10.18372/2306-1472.69.11055

Keywords:

acoustic emission, composite material, dispersion properties, distraction, energy, machining, signal

Abstract

Purpose: The aim of this study is to investigate the influence of treated composite material dispersion properties on acoustic radiation energy, which appears during composite material machining. Methods: The researches were grounded on simulation of acoustic radiation energy at change of mechanically treated composite material properties dispersion for the mechanical model of its surface layer destruction. The data processing with definition of acoustic radiation statistical energy parameters was conducted. The analysis of acoustic emission energy parameters sensitivity to change of composite material properties dispersion, and as the analysis of influencing of composite material properties dispersion on AE amplitude and energy parameters was conducted. Results: Were obtained that at decreasing of composite material properties dispersion there is increasing an average level of acoustic radiation energy and value of its deviation. Is determined, that at decreasing of composite material properties dispersion the greatest increasing there is an acoustic emission energy average level dispersion. It is show that the increasing of acoustic radiation energy parameters advances increasing its amplitude parameters. Discussion: The simulation of acoustic radiation energy at composite material machining for the mechanical model surface layer destruction at decreasing of composite material properties dispersion (spread) is conducted. It is shown, that the decreasing of composite material properties dispersion does not influence on acoustic radiation energy nature change. At the same time, the ascending parameter, that describing of composite material properties dispersion decreasing, results in increase of acoustic radiation signal energy parameters. The obtained outcomes can be used at mining methods of verification, diagnostic and monitoring of composite material machining technological processes. Thus during the composite material machining is possible to control and to determine of composite material properties rejection by analysis of acoustic emission signal energy average level dispersion.

Author Biography

Sergii Filonenko, National Aviation University

Doctor of Engineering. Professor.

Director of the Institute of Information-Diagnostic Systems, National Aviation University, Kyiv, Ukraine.

Education: Kyiv Polytechnic Institute, Kyiv, Ukraine (1977).

Research area: diagnostics of technological processes and objects, automatic diagnostic systems.

References

Olufayo O.A., Hossein K.A.E. (2013) Acoustic Emission Monitoring in Ultra-High Precision Machining of Rapidly Solidified Aluminum. Proceedings of the International Conference on Competitive Manufacturing (30 January - 1 February, 2013, Stellenbosch, South Africa), pp. 307-312.

Prasanth R., Prabukarthi A., Kumar M. Senthil, Krishnaraj V., Rajamani R. (2015) Identification of drill position in CFRP/Titanium alloy stacks using acoustic emission signals. Proceedings of International Conference on Advances in Materials, Manufacturing and Applications - AMMA 2015 (April 9-11, Trichy, India, 2015), pp. 1174-1181.

Tang D., Lim H.B., Lee K.J., Ha S.J., Kim K.B., Cho M.W., Park K., Cho W.S. (2013) Mechanical properties and high speed machining characteristics of Al2O3-based ceramics for dental implants. Journal of Ceramic Processing Research, vol. 14, no. 5, pp. 610-615.

Devendiran S., Manivannan K. (2013) Condition monitoring on grinding wheel wear using wavelet analysis and decision tree C4.5 algorithm. International Journal of Engineering and Technology, vol. 5, no. 5, pp. 4010-4024.

Ronald B.A., Vijayaraghavan L., Krishnamurthy R. (2007) Studies on grooving of dispersion strengthened metal matrix composites. Materials forum, vol. 31, pp. 102-109.

Fadare D.A., Sales W.F., Bonney J., Ezugwu E.O. (2012) Influence of cutting parameters and tool wear on acoustic emission signal in high-speed turning of Ti-6Al-4V alloy. Journal of Emerging Trends in Engineering and Applied Sciences, vol. 3, no. 3, pp. 547-555.

Hase A. (2013) Acoustic emission signal during cutting process on super-precision micro-machine tool. Proceedings of Global Engineering, Science and Technology Conference (3-4 October, 2013, Bay View Hotel, Singapore), pp. 1-12.

Mukhopadhyay C. K., Jayakumar T., Raj B., Venugopal S. (2012) Statistical analysis of acoustic emission signals generated during turning of a metal matrix composite. J. of the Braz. Soc. of Mech. Sci. and Eng., vol. 34, no. 2, pp. 145-154

Shoba C., Ramanaiah N., Rao D.N. (2015) Effect of reinforcement on the cutting forces while machining metal matrix compositese an experimental approach. International Journal Engineering Science and Technology, vol. 18, pp. 658-663.

El-Kady E.Y., Gaafer A.M., Ghaith M.H.G., Khalil T., Mostafa A.A. (2015) The effect of machining parameters on the cutting forces, tool wear, and machined surface roughness of metal matrix nano composite material. Advances in Materials, vol. 4, no. 3, pp. 43-50.

Mahamani A. (2011) Machinability study of Al-5Cu-TiB2 in-situ metal matrix composites fabricated by flux-assisted synthesis. Journal of Minerals, Materials Characterization and Engineering, vol. 10, no. 13, pp. 1243-1254.

Filonenko S.F. (2015) The connection of acoustic emission with a properties dispersion of composite material machining. Proceedings of the National Aviation University, no. 3(64), pp. 105–110.

Fylonenko S.F. (2015) Vlyianye dyspersnosty svoistv kompozyta na akustycheskoe yzluchenye pry mekhanycheskom razrushenyy poverkhnostnoho sloia [Influence of composite properties dispersion on acoustic radiation at mechanical destruction of surface layer]. Tekhnolohycheskye systemy, no. 3(72), pp.109-115.

Filonenko S.F. (2015) Simulation of acoustic radiation energy at composite mechanical destruction surface layer. Electronics and Control Systems, no. 4(46), pp. 90-96.

Published

21-11-2016

How to Cite

Filonenko, S. (2016). ACOUSTIC ENERGY AT CHANGE OF TREATED COMPOSITE MATERIAL DISPERSION PROPERTIES. Proceedings of National Aviation University, 69(4), 56–63. https://doi.org/10.18372/2306-1472.69.11055

Issue

Section

MODERN AVIATION AND SPACE TEHNOLOGY