Acoustic energy at controlled cutting depth of composite material

Authors

  • S. F. Filonenko National Aviation University

DOI:

https://doi.org/10.18372/1990-5548.49.11244

Keywords:

Acoustic emission, composite material, signal, model, energy, machining, wear, control, statistical characteristics

Abstract

The simulation of acoustic radiation energy at machining composite material and treating toolwearing for a case of controlled cutting depth is conducted. It is shown, that at controlled cutting depthwearing of the treating tool results in increasing acoustic radiation energy parameters. Is determined,that the increase of acoustic radiation energy average level dispersion advances increase of its averagelevel and standard deviations. It is shown, that the increasing of acoustic radiation energy parametersadvances increasing its amplitude parameters deviation

Author Biography

S. F. Filonenko, National Aviation University

Doctor of Engineering Science. Professor. Educational-Scientific Institute of Information Diagnostic Systems

References

B. A. Ronald, L. Vijayaraghavan, and R. Krishnamurthy, “Studies on grooving of dispersion strengthened metal matrix composites,” Materials

forum, vol. 31, 2007, pp. 102–109.

C. K. Mukhopadhyay, T. Jayakumar, B. Raj, and S. Venugopal, “Statistical analysis of acoustic emission signals generated during turning of a metal matrix composite,” J. of the Braz. Soc. of Mech. Sci. and Eng., vol. 34, no. 2, pp. 145–154, 2012.

O. A. Olufayo and K. A. E. Hossein, “Acoustic Emission Monitoring in Ultra-High Precision Machining of Rapidly Solidified Aluminum,” Proceedings of the International Conference on Competitive Manufacturing (30 January-1 February, 2013, Stellenbosch, South Africa), 2013, pp. 307–312.

Y. Wei, Q. An, X. Cai, M. Chen, and W. Ming, “Influence of Fiber Orientation on Single-Point Cutting Fracture Behavior of Carbon-Fiber/Epoxy Prepreg Sheets,” Materials, vol.8, 2015, pp.6738–6751.

F. Qin, J. Hu, Y. K. Chou, and R. G. Thompson, “Delamination wear of nano-diamond coated cutting tools in composite machining,” Wear, vol. 267, pp. 991–995, 2009.

P. Lu, “An investigation into interface behavior and delamination wear for diamond-coated cutting tools,” A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the department of mechanical engineering in the Graduate School of the University of Alabama, 155 p.

D. A. Fadare, W. F. Sales, J. Bonney, and E. O. Ezugwu, “Influence of cutting parameters and tool wear on acoustic emission signal in highspeed turning of Ti-6Al-4V Alloy,” Journal of Emerging Trends in Engineering and Applied Sciences, vol. 3, no. 3, pp. 547–555, 2012.

M. Prakash, M. Kanthababu, S. Gowri, R. Balasubramaniam, and J. R. Jegaraj, “Tool condition monitoring using multiple sensors approach in the micro end milling of aluminum alloy (AA1100),” 5th International & 26th All India Manufacturing Technology, Design and Research Conference -AIMTDR 2014 (12-14 December, 2014, IIT Guwahati, Assam, India), 2014, pp.394-1–394-6.

L. F. Chang, M. C. Lu, K. H. Chen, and C. C. Wu, “Development of Condition Monitoring System for Micro Milling of PZT Deposited Si Wafer,” 9-th International workshop on microfactories - IWMF2014 (5-8, October, 2014, Honolulu, U.S.A.), 2014, pp. 139–145.

B. Giriraj, “Prediction of progressive tool wear using acoustic emission technique and artificial neural network,” Journal of Civil Engineering Science, vol. 1, no. 1-2, pp.43–46, 2012.

S. F. Filonenko, “Influencing of cutting tool wearing at a controlled cutting depth on acoustic Emission,” Eastern-European Jornal of enterprise technologies, no. 6/9(78), pp. 47–50, 2015. (in Russion).

S. F. Filonenko, T. V. Nimchenko, and A. P. Kosmach, “Model of acoustic emission signal at the prevailing mechanism of composite material mechanical destruction,” Aviation, vol. 14, no. 4, pp. 95–103, 2010.

S. F. Filonenko and A. P. Kosmach, “Acoustic emission in composite materials friction,” Aviation, vol. 18, no. 2, pp. 57–63, 2014.

S. F. Filonenko, “Simulation of acoustic radiation energy at composite mechanical destruction surface layer,” Electronics and Control Systems, no. 4(46), pp. 90–96, 2015.

Downloads

Issue

Vol. 3 No. 49 (2016)

Section

MATHEMATICAL MODELING OF PROCESSES AND SYSTEMS

License

Authors who publish with this journal agree to the following terms:

Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).